ADVANSEA AIS RX-100 DRIVER

ADVANSEA AIS RX-100 DRIVER

July 17, 2020

Please ensure all items are present and if any of the items are not present contact your dealer. When reading this manual please pay attention to warnings marked with the warning triangle shown on the left. Check that the connections to the chart plotter are correct. Class A transceivers transmit at a higher VHF signal power than class B transceivers and therefore can be received by more distant vessels, and also transmit more frequently. Class A transceivers are mandatory on all vessels over gross tonnes on international voyages and certain types of passenger vessels under the SOLAS mandate. Please refer to your chart plotter manual for more information. Connect the red wire to the power supply positive terminal.

Uploader: Samut
Date Added: 13 January 2010
File Size: 13.37 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 90951
Price: Free* [*Free Regsitration Required]

There are two categories of information transmitted by an AIS transceiver: Means of connecting the cables together will also be required.

Advansea RX Dual Channel AIS Receiver

Class B transceivers transmit at a lower power and at a lower reporting rate than class A transceivers. Please refer to Figure 6 for guidance. Antenna cables Alternatively, if you wish to use an existing VHF antenna, antenna splitter products are available which allow the existing antenna to be used with two radio devices, aia as a VHF voice radio and the AIS RX Compass safe distance 1. Please refer to your chart plotter manual for more information.

This equipment must be installed and operated according to the instructions contained in this manual. The NMEA data port provides the connection to your chart plotter and consists of four wires colour coded as shown in the table below and in Figure 8.

  HP PSC 1315 ALL-IN-ONE PRINTER SCANNER COPIER DRIVER DOWNLOAD

advanSea AIS RX-100 Receiver

In addition to the items provided with your AIS RX the following items will be required for installation: We constantly strive to achieve the highest possible quality standards, should you encounter any problems with this product, please contact your dealer who will be pleased to offer whatever assistance you require.

You may also need to enable the display of AIS targets in the chart options. Class A transceivers are mandatory on all vessels over gross tonnes on international voyages and certain types of passenger vessels under the SOLAS mandate. If your VHF antenna does not use this type of connector rxx-100 contact your dealer for details of available adaptors.

Please refer to section 3. Similar to class A transceivers in many ways, but are normally lower cost advsnsea to the less stringent performance requirements.

Please ensure all items are present and if any of the items are not present contact your dealer. Thank you for buying this AIS receiver.

If you are using charting software running on a PC, please refer to the instructions provided with your chart plotting software for details of how to configure it to display AIS information.

Any attempt to tamper with or damage this product will invalidate the warranty. Please ensure your NMEA device operates at baud.

This equipment is intended as an aid to navigation and is not a replacement for proper navigational judgement. The status indicator will illuminate when power is applied to the unit and it is running in normal mode. It is recommended that crimped and soldered lugs are used to connect the AIS RX to the power source. It’s a community-based project which helps to repair anything.

  ENV3 VX9200 DRIVER DOWNLOAD

AdvanSea RX-100 AIS Receiver

Do not install this equipment in a flammable atmosphere such as in an engine room or near to fuel tanks. If you require longer cables to reach your power supply, please ensure the cables are capable of carrying an average current of up to mA. Also included on the CD is the product manual. The NMEA data port output operates at a baud rate of baud. Disposal of this product and packaging!

It is strongly recommended that you read all of the instructions in this manual prior to installation. Check that the connections to the chart plotter are correct. Connect the black wire to the supply negative terminal.

advanSea Rx Dual Channel Ais Receiver | eBay

Connect the red wire to the power supply positive terminal. These are important messages for safety, installation and usage of the product. Class A transceivers transmit at a higher VHF signal power than class B transceivers and therefore can be received by more distant vessels, and also transmit more frequently.

Posted in Battery